Browse by Type
PanicExitPro.com is designed to provide an easy solution for commercial door access and crash bar exiting. We aim to make a Pro out of even the first time installer. We supply easily installed surface mount rim style panic exit bars that can be installed with very little expertise.
Some considerations to be made when choosing your panic exit bar:
Single door panic exit installation on a glass door or narrow stile door:
Although the measurements on the panic bars may seem to fit the stile of your door, (a stile is the vertical area on the sides of the door that you are going to use for mounting commercial door hardware) standard one point latch bars have some complications when using outside trim or with glass doors. Outside trim increases the width of the stile needed to approximately 5 inches. the 2000 series panic exit bar has a special lever handle made for narrow stiles. Also with glass doors the aesthetics of what is seen through the door should be considered. With a standard panic exit bar the rear is not meant to be seen and would not be pleasing to see through the glass.
Dual door panic exit bar installation when doors overlap:
The number one instinct when equipping a dual door with panic exit bars is to put top and bottom 2 point latch vertical rod panic exit bars on each door. However if there is an overlap this would restrict exiting to a single door. Check out our video above for a demonstration on why to pair a side latch
1 point crash bar with a 2 point crash bar.
Access from the exterior:
Panic exit bars are designed the same in which you will always have a manual exit from the building, that choice is easy. However what is not as easy to decide if and how to allow access from the exterior. Depending on the purpose of the door you may decide to not have any door trim on the outside. If the door is not a heavily used exterior door you may use a crash bar with cylinder lock access and put a dummy pull handle on the outside. This would result in key access only and automatic locking as soon as the key is removed from the door. If the door is heavily used outside trim such as knob
or lever handles can be used. In this case the handle would be locked or unlocked and general access can be allowed. Lastly for higher security properties that must allow general access electronic access can be paired with all of the surface mount panic exit bars. This has nearly unlimited variations of access possibilities.
Panic Bar Accessories
- Ergonomically correct
- Aesthetically pleasing
- Dimensions: 4.7" x 1.7"
- Easy to install
- *THREE options: dummy, key alike, key unique
- Keyed models designed with a built in lock to eliminate the need for a cylinder lock
- Pedestrian Key Release Style
$58.99
- Dimensions: 4.7" x 1.7"
- Easy to install
- Three options: keyed unique, keyed unique with master key, keyed alike
- Pedestrian Key Release Type
$58.99
- Easy to install
- Finished in stainless steel for durability
- Appropriate for outdoor applications
$46.50
- Includes manual and screws for easy installation
- Is designed for low to medium usage and outdoor entryways
- Is compatible with all panicexitpro.com emergency exit bars
- Includes a built in lock, eliminating the need for a cylinder lock
$63.00
- Dimensions: 11.8" x 3.1" x 2.5"
- Constructed with a stainless steel finish
- Easy to install
- Comes in dummy trim style or with pre-cut hole
- Recommended for use with the 300 and 500 series emergency exit bars
$25.99
- Compatible with series 2000 panic exit bars
- Can be used right or left handed
$32.99
- Easy to install
- Constructed of stainless steel
- Difficult to tamper with because of its compact design
- Recommended for use with the 300 and 500 series emergency exit bars
- Appropriate for low traffic entryways
$8.99
- L: 6″ x W: 3 1/4″ x D: 2 3/4″
- Schlage Keyed Cylinder
- Stainless Steel Construction
- Compatibility with LockeyUSA PB1100, PB2500, and Detex v40 panic exit bars
- L: 6″ x W: 3 1/4″ x D: 2 3/4″
- Free Passage
- Stainless Steel Construction
- Compatibility with LockeyUSA PB1100, PB2500, and Detex v40 panic exit bars
- L: 13 3*4″ x W: 3″ x D: 2 1/2″
- Panic Trim
- Schlage Keyway
- Thumbpiece Keyed Entry Trim
- Stainless Steel Construction
- Compatibility with LockeyUSA PB1100, PB2500, and Detex v40 panic exit bars
- L: 13 3*4″ x W: 3″ x D: 2 1/2″
- Panic Trim
- Pull Handle Entry Trim
- Stainless Steel Construction
- Compatibility with LockeyUSA PB1100, PB2500, and Detex v40 panic exit bars
- L: 13 3*4″ x W: 3″ x D: 2 1/2″
- Panic Trim
- Schlage Keyway
- Stainless Steel Construction
- Compatibility with LockeyUSA PB1100, PB2500, and Detex v40 Panic exit bars
- Dimensions H: 7 5/16″ x W: 2 3/16 x D: 2 3/8″
- 1150 Lock Body
- Compatible with LockeyUSA PB1100, PB2500, and Detex V40
- Compatible with panic bars that accept a flat tailpiece and have a turn radius less than 74 degrees
- Magnet-proof
- Keyless Panic Trim
- Made for Detex Panic Bars
- Heavy Duty Lever
- Passage Function
- Lifetime Mechanical Warranty
- Finish Options Available
- Dimensions H: 5 5/8″ x W: 1 5/8 x D: 2 1/4″
- 2835 Lock Body
- Compatible with LockeyUSA PB1100, PB2500, and Detex panic exit bars
- Compatible with panic bars that accept a flat tailpiece and have a turn radius less than 74 degrees
- Magnet-proof
- Passage Function
- Keyless Panic Trim
- Made for Detex Panic Bars
- Non-handed
- Easy to change combination
- Easy to install
- Covers standard 2 1/8" hole
- Dimensions: 6 1/2" H x 1 3/4" W x 2" D
- 3210 Lock Body
- Compatible with LockeyUSA PB1100, PB2500, and Detex panic exit bars
- Compatible with panic bars that accept a flat tailpiece and have a turn
radius less than 90 degrees
- Magnet-proof
- Dimensions: L: 1 1/8" X W: 1 3/8" X D: 1 3/8"
- Compatibility with PSGB5 and EDGB5 key boxes (Not
included)
- Schlage Keyway
- Two Keys Included
- Can be used with the Lockey PB1100 Series Panic Bars
- Adjustable for 28" to 54" Gate
- Shield Size: 12"H
- Depth 1/2 "
- Powder Coated
- 16 Gauge Electro-Galvanized Steel
- Mounting plate for PB1100, PB2500, and Detex V40 Panic Bars
- Black Stainless Steel Design
- For dual doors with no column
- Max door height: 8 feet
$22.95
- Stainless Steel Design
- For dual doors with no column
- Max door height: 8 feet
$22.95
- Help apply commercial panic door and emergency exit door hardware
- Are designed for use on non-solid metal doors
- Come in a set: one female & one male
- Offer a sturdy stainless steel design
- This is a pack of 6
- Designed to cover gaps in the door jamb after locks have been changed
- Assists in security of door
- Affordably priced
- Has two pre-drilled holes
- Designed to cover gaps in the door jamb after locks have been changed
- Assists in security of door
- Affordably priced
- Has four pre-drilled holes
- Designed to cover gaps in the door jamb after locks have been changed
- Assists in security of door
- Affordably priced
- Has two pre-drilled holes
- Designed to cover smaller sized holes
- For Rim & Mortise Cylinders
- 2-5/8" Outside Diameter
- 1-1/4" Inside Diameter
- Push to test switch
- Injection-molded, VO flame retardant, high impact
- Charge rate/power on LED indicator light
- LED lamp life of 25 years plus
- Listed for damp locations
- Universal mounting canopy for top or side installation (wall or ceiling)

- Battery Backup
- Test Switch/LED charge indicator provide
- Suitable for Damp Locations
- Charge Rate/Power On LED Indicator Light
- Injection-molded thermoplastic housing
- Square-shaped light heads that are easy to adjust without tool requirement